DISCLAIMER

All rights of photos and text reserved. Usage of photos or text from my blog on other websites or for any other purpose only with prior permission. If you want to use any material from my blog please contact me by email.

Tuesday, December 25, 2012

Listening to the all DHT amplification chain

Hi!

I have been extensively experimenting with the DHT gain stage in the recent days and would like to share some listening impressions.





As an initial test it replaced the output section of the E55L LCR phono stage which I've been using recently. The E55L input stage feeding the 600 Ohm LCR RIAA EQ, from there straight into the DHT gain stage. Since it has quite a lot of gain, no step up transformer at the input of the DHT stage. From there into the 6AH4 line stage and then into a 10Y/45 power amp.

Although this was a strange mix of IDHTs and DHTs it gave a good first impression about the suitability of the 841 and 801 in a phonostage. Microphonics were surprisingly low due to the use of vibration damped tube sockets. Noise and hum also very low. Initial sound impressions were excellent. Very smooth and detailed.

But the real question was, would this DHT gain stage also be usable at the input side of the phono, enabling an all DHT amplification? Or would noise and microphonics render it impractical? I hauled the 10Y linestage up from the basement. To give an all DHT amplification chain a try.




The result is amazing. No appreciable microphonics. Noise and hum levels absolutely ok! Sure when you tap the first tube in the chain you hear it ringing in the speakers. Hum and noise are not as low as with the E55L or EC8020. But absolutely not objectionable at all.

This is an amplification chain now which is purely built with directly heated triodes: Lundahl LL1933Ag silver MC step up transformer wired 1:16 feeding the grids of the 841 tube. The 841 is DC coupled to a 801 which drives the Tango LCR EQ through a 4.5:1 step down transformer. The output of the LCR EQ is connected to a transformer input of the 10Y linestage with 1:11,2 step up. The linestage uses a Tribute line output / transformer volume control. Connected to the linestage is a power amp with a 10Y  as driver and 45 as output tube. Directly heated all the way and thoriated tungsten filaments up to and including the driver stage of the power amp.




Anybody who has experienced the difference in sound when changing a tube from indirectly to directly heated has an idea of the sound of this set up. It is extremely detailed without a hint of annoyance which high resolution systems often have. The DHTs sound very smooth and musical. Almost scary lifelikeness.



 
 
These initial listening tests had been done with fairly regular tubes. Hytron VT51 (military number of the 841) and Taylor VT62 (military version of the 801). Both with metal plates.
 
In the linestage I usually get best results in terms of microphonics from graphite plate and ceramic socket 801s. So I was curious how such tubes would perform in the phono. Surprisingly the graphite plate 841 from Mazda were more microphonic than the metal plate Hytrons. Still usable, but microphonics at a level as one would except in the phono.
 
 
 
 
 
My favorites! Surprisingly low in microphonics and noise. Very detailed. Voices are so beautiful through these triodes! Almost unreal!
 
Does this render the IDHT phonostages obsolete? No, certainly not! A properly implemented LCR phonostage is reproducing at a very high quality level. A DHT version is for the DHT lovers who seek that special magic only directly heated tubes have. A IDHT phonstage is far more practical. A DHT phonostage will always remain rather insane and demand more maintenance. Tubes require some selection for low microphonics, any tiny problem with a tube becomes very obviously audible.
 
Gain in this set up is on the low side, but sufficient for most of my listening situations. With other power amps or recordings with a low level another amplification stage might be useful. Or when the volume shall be really cranked up. Say a single stage 801 with input and output transformer giving another 12dB. But I have been happily listening to it as is. I even switched to the lower step up transformer input at the linestage (12dB).
 
The power supplies got a new look. I decided to experiment with wooden transformer covers:




Best regards

Thomas

6 comments:

  1. Hallo Thomas,
    ist es möglich, auch diesen Beitrag ins deutsche zu übersetzen?
    Viele Grüße
    Rolf

    ReplyDelete
  2. Hallo Rolf,

    gerne, werde ich im Januar übersetzen und einstellen.

    Viele Grüße

    Thomas

    ReplyDelete
  3. Hi Thomas, do you plan to do an article in more detail about the DHT phono stage? How do you feel the Tango LCR compares to the Intact Audio one? Cheers

    ReplyDelete
  4. Hi Deepak,

    which details would you expect in a further article? Contrary to other projects I published the schematic and also showed detailed photos of the construction. I am currently building two more DHT phonos for other people. If I get new insights during those build, I will report them.

    The Tango LCR units are complete with capacitors, while intactaudio only makes the coils. So a direct comparison is difficult. If top quality caps are used the performance is on a similar level. I am about to build LCR RIAAs with silver wound intactaudio coils. There is a good chance these will be superior.

    Best regards

    Thomas

    ReplyDelete
    Replies
    1. Hi Thomas, I am just curious which tubes you used and how much gain it has. Is this discussed more in one of the modular preamplifier articles?

      I have a 0.3 mv Soundsmith Paua coming and am very interested in DHT phono with LCR

      Delete
  5. Hi!

    As described gain is very low and needs a dedicated linestage with a step up input to get enough gain. With the linestage together I get under the usual 40dB. Plus the gain from the MC step up transformer used.

    Best regards

    Thomas

    ReplyDelete