DISCLAIMER

All rights of photos and text reserved. Usage of photos or text from my blog on other websites or for any other purpose only with prior permission. If you want to use any material from my blog please contact me by email.

Tuesday, September 30, 2014

SE 45 amp made switchable to 300B

Hi!

Last year I showed a 45 amplifier with a driver stage which could accept either another 45 or a 10Y. The owner of the amps requested them to be modified so they can also use the 300B as output tube.





It is relatively simple to make an amplifier such that it can accept either a 45 or 2A3 output tube as was done in this amp. The 45 and 2A3 use similar operating voltages. While the 300B could be run at a low operating point using the same voltage as the 45, this would not use it's full potential. So a more elaborate switching scheme is necessary to set the amp correctly for either tube, hence two switches. To easily monitor filament voltage, two measurement jacks were added as well. The switchability of the driver stage was kept.




Filament measurement jacks were added for the driver as well. The power supply also received a switch to set the different supply voltages:




And finally for covering to all kinds of situations, a set of switch was added to the back for adjustment of filament voltages over a wide range. This allows to adjust the filaments by accessing different taps of the filament transformer, in case some tubes are used with filament specs that do not match the originals. There are cases of new production tubes which draw much higher filament current. The filament voltages are DC for driver and output tubes for hum free operation.




The complete set of mono blocks with their power supplies, here equipped with ceramic base 801 in the driver sockets and Electro Harmonix 300B output tubes.




These amplifiers allow a variety of combinations. A tube rollers dream. Here one of my favourites, 10Y drives 300B, in this case an old production Western Electric:




The 10Y driving a 45:




45 drives 45:




Globe 45s:




EML makes ridiculously large 45s. Here a mesh plate in the driver position and a solid plate output tube:




The EML 45 is even larger than the Western Electric 300B:




The Tango XE20S output transformer allows a wide flexibility in primary impedance to cover this variety of tubes. To make use of it's full potential, all taps of the output transformer are brought out to speaker jacks:




As soon as the new Elrog 300Bs arrive these will also be evaluated in this amp. Please don't expect me to give sound descriptions of all these combinations. This is highly subjective and I learned that different users of such switchable amps seem to develop different preferences. I will run some listening sessions during the next days and report my impressions on some of the combinations. Stay tuned.

Best regards

Thomas

7 comments:

  1. Hi Thomas,

    Cool.. One could go crazy with the combinations. And maybe a version that could accomodate DHT 50's (NOS or EML) for the outputs too. Or maybe even use socket adapters for 46's.

    ReplyDelete
    Replies
    1. Hi!

      Honestly I am more a fan of pure and simple amps which just accept one tube type. Plug in, switch on, enjoy and forget. Like the silver '45 bliss' amps. But if someone absolutely wants it switchable, I won't say no ;-)

      But that's just me, once an amp plays I am just too lazy to change tubes.

      Also keep in mind the more tube types you make the amp for, the more compromises you have to accept. Nothing beats an amp optimised for one tube only.

      Best regards

      Thomas

      Delete
  2. Hi Thomas,

    Yes, very true, re: less compromise with "fixed" valves for optimized op points and iron.. But if I had the funds, I'd at least go for switchable outputs only, for two types of DHT's.. Maybe a 300B/50. Only the filament voltages needs to be switched, nothing else. Maybe use ~5k primaries with silver wired Finemet core OPT's for both =)..

    ReplyDelete
    Replies
    1. Hi!

      Yesss, silver wired Finemet core OPTs! More about that in this theatre soon! stay tuned!

      Thomas

      Delete
  3. Hi Thomas!

    The filament switches are really very helpful to adjust different tubes and it works flawless. Even switching during operation is ablsolutely without any plop.

    On the other hand there is another big advantage. You can measure the grid voltage and check if both tubes settle down to an comparable operating point.

    BR!
    Bernd

    ReplyDelete
    Replies
    1. Hi Bernd!

      Thanks for the feedback! I am glad that you enjoy the amps!

      Best regards

      Thomas

      Delete
  4. Hi at all. Someone know a diagram for one amplifier with 45 tube driver and 300B Power tube ?

    Thanks

    Santiago

    ReplyDelete